UNIVERSITAS AIRLANGGA



Detail Article

The Indonesian Journal of Occupational Safety and Health

ISSN 2301-8046

Vol. 3 / No. 2 / Published : 2014-12

Order : 4, and page :148 - 159

Related with : Scholar   Yahoo!   Bing

Original Article :

Risk assessment pada pekerjaan di bagian press cutting pt. x

Author :

  1. Mulyono*1
  2. Ema Kusumawati*2
  1. Dosen Fakultas Kesehatan Masyarakat
  2. Mahasiswa Fakultas Kesehatan Masyarakat

Abstract :

ABSTRACT Accidents are unexpected events and expected not related to work in the company. Number of accidents can be reduced by risk management for the company to avoid any possibility that could hurt the company. One of them with a risk assessment. This study aims to perform a risk assessment on a press cutting jobs in PT. X. This study is a descriptive study using cross- sectional design and analyzed descriptively. The data used are primary data from observational and interview as well as secondary data from the company. The population in this study was a worker at the press cutting in PT. X as many as 38 people. The data were analyzed descriptively. From the results, 10 the potential hazards of the 5 activities that are on the cutting press with 3 extreme risk, 2 high risk, 4 moderate risk, 1 low risk. The resulting residual risk is as much as 8 residual risk that needs consideration. The conclusion is that there is the risk of press cutting jobs classified as high risk. Control of the risks undertaken by the company is good but still have to be improved because the resulting residual risk is still more than 50%. Advice can be given which needs to create Job Safety Analysis and risk assessment, providing PPE (safety shoes, ear plugs), a more stringent warning to workers who are not using PPE, provide rewards to improve worker motivation, using sawdust to clean up oil spills, and gives tire cover to the hand pallet. Keywords: risk assessment, potential hazards, risk assessment control, residual risk

Keyword :

risk assessment, potential hazards, risk assessment control, residual risk,


References :

Lester; and John,(1994) Pedoman Bagi Penyelia 2 Jakarta Pusat : PT. Pustaka Binaman Pressindo dan LPPM

Maurits, Lientje Setyawati K,(2010) Selintas Tentang Kelelahan Kerja. Yogyakarta : Amara Books

Notoadmodjo, Soekidjo,(2005) Metodelogi Penelitian Kesehatan Jakarta : PT Rineka Cipta

OHSAS,(2007) Occupational Health and Safety Management Systems Dundee : British Standards

Ramli, Soehatman,(2010) Pedoman Praktis Manajemen Risiko dalam Perspektif K3 OHS Risk Management Jakarta : PT. Dian Rakyat

Ramli, Soehatman,(2010) Sistem Manajemen Keselamatan dan Kesehatan Kerja OHSAS 18001 Jakarta : PT. Dian Rakyat

Ridley, John,(2006) Kesehatan dan Keselamatan Kerja Jakarta : Erlangga

Suardi, Rudi,(2005) Sistem Manajemen Keselamatan dan Kesehatan Kerja: Panduan Penerapan Berdasarkan OHSAS 18001 & Permenaker 05/1966 Jakarta : PPM

Suma’mur,(2009) Higiene Perusahaan dan Kesehatan Kerja (Hiperkes) Jakarta : CV Sagung Seto

Supono,Arief,(2011) Him



Archive Article

Cover Media Content

Volume : 3 / No. : 2 / Pub. : 2014-12
  1. Hubungan Pemenuhan Kebutuhan Kalori Kerja Dengan Produktivitas Di Pabrik Sepatu
  2. Risk Assessment Kecelakaan Kerja Pada Unit Windin Pt. Kusumaputra Santosa, Karanganyar, Jawa Tengah
  3. Analisis Hubungan Faktor Pekerjaan Dengan Stres Kerja Bidan Di Rumah Sakit Syamrabu Bangkalan
  4. Risk Assessment Pada Pekerjaan Di Bagian Press Cutting Pt. X
  5. Analisis Tingkat Risiko Muskuloskeletal Disorders (msds) Dengan The Rapid Upper Limbs Assessment (rula) Dan Karakteristik Individu Terhadap Keluhan Msds
  6. Risk Assessment Pada Pekerja Maintenance Di Pt X
  7. Analisis Faktor Karakteristik Individu Yang Berhubungan Dengan Tindakan Tidak Aman Pada Tenaga Kerja Di Perusahaan Konstruksi Baja
  8. Penerapan Csms (contractor Safety Management System) Sebagai Upaya Pencegahan Kecelakaan Kerja
  9. Kelengkapan Pemenuhan Syarat Operator Ketel Uap Dengan Upaya Pengoperasian Dan Pemeliharaan Di Pt Pupuk Kaltim (studi Pada Operator Di Industri Kimia)
  10. Fault Tree Analysis (fta) Pada Bagian Electric Arc Furnace Di Pt. X

Information K3